Measurement and testing
The US Environmental Protection Agency (EPA) is not proposing to weaken the emission limits for gasoline terminals and bulk plants. It is proposing to change how operators prove they are meeting them.
For anyone running analysers, temperature instruments or leak surveys at these sites, that distinction matters more than the headline.
The proposal, published in the Federal Register on Monday, 28 September 2026 (91 FR 61175, docket EPA-HQ-OAR-2025-0302), reconsiders parts of the rule EPA finalised on Wednesday, 8 May 2024.
That rule created new performance standards for bulk gasoline terminals (40 CFR part 60, subpart XXa). It also revised two air toxics standards: subpart R for major sources and subpart BBBBBB for area sources.
EPA had agreed to reconsider it on Friday, 28 February 2025, after petitions from industry. The comment period closed on Thursday, 12 November 2026.
EPA says the changes do not alter the stringency of any emission standard and that it expects no change in volatile organic compound (VOC) or hazardous air pollutant (HAP) emissions.
It states it is not reopening any other aspect of the 2024 rule.
The most consequential changes for monitoring sit in the continuous compliance provisions for loading-rack control devices.
For vapour recovery units, the averaging period for the outlet concentration limit would double, from a three-hour rolling average to a six-hour rolling average. The limit itself does not change.
A longer window does, however, absorb short excursions that a three-hour average would have recorded as deviations.
Data reviewers and continuous emission monitoring system (CEMS) owners should expect fewer flagged periods from the same underlying performance.
The proposal also changes what happens when a CEMS is down. The 2024 rule relied on operating parameters from the previous ten operational cycles to cover CEMS downtime.
EPA now proposes that facilities develop and submit a site-specific monitoring plan instead. That shifts the burden from a fixed formula to a documented, site-specific justification.
For thermal oxidisers, EPA has co-proposed two ways of setting the temperature operating limit. One is based on revised performance test requirements. The other is a fixed minimum mid-stack temperature of 400°F (around 204°C).
A fixed surrogate is simpler to audit but is not tied to the destruction efficiency demonstrated at a particular unit.
EPA also proposes changing how burner diameter is treated in the dilution net heating value (NHVdil) calculation for multi-burner systems. Maximum air-assist rates would be set by reference to the performance test.
For bulk gasoline terminals under subpart XXa, EPA proposes a capital expenditure threshold to decide when a change counts as a modification.
A project would not trigger the equipment leak programme if its cost stayed below a defined share of the equipment’s replacement cost. The proposal uses a basic repair allowance of 8.0 per cent.
A new definition of ‘process improvement’ would cover routine safety, maintenance and environmental control changes.
Where the leak programme does apply, the proposal sets the first instrument monitoring survey within 180 days of a source becoming subject to the requirements.
It also requires monitoring during active gasoline loading into cargo tanks, when components are under the conditions most likely to reveal leaks.
The first leak survey at existing sources is reported to be due by Saturday, 8 May 2027.
EPA is also reported to have said it is not proposing changes to the 2024 rule’s compliance dates [unverified – trade summary only; check against the Federal Register text].
EPA also revisits the vapour tightness requirements for gasoline cargo tanks, responding to concerns about whether the 2024 values were feasible.
Trade reports describe a return to graduated, capacity-based pressure and vacuum change limits used before 2024 [unverified – numeric values not confirmed against the Federal Register text]. Testing continues to rely on EPA Method 27.
EPA’s fact sheet estimates industry savings of around US$9.1m between 2027 and 2041, in 2024 dollars.
For area sources, the proposal puts annual savings at between US$565,800 and US$713,400, depending on which monitoring option is chosen.
Those figures are small against the scale of the sector. The more lasting effect is on data.
Longer averaging windows, a fixed temperature surrogate and site-specific downtime plans all change what a compliance record shows, even if the permitted emission rate stays the same.
Operators and their instrument suppliers will want to see which options EPA finalises before reconfiguring data acquisition systems and reporting logic.
PIN 27.5 Oct/Nov 26